Seat sliders Sparco 
Be the first to review “Pivot Plate” Cancel reply
Pivot Plate
20.16€ – 45.97€
- Pivot plate for fixing two aluminum profiles together
- Usually to mount a side monitor in a triple screen setup
- 40 degree scale for adjusting the pivot (+/- 20 degrees)
- Can be used in other than alu-profile rigs as well, if the construction is suitable
- Mounting holes are for M8 bolts
- Material: 5 mm aluminum, matte black
- Sold in kits of two and four
- Optional: M8 bolts, washers and T-nuts
- 8 pcs each if 2 plates selected
- 16 pcs each if 4 plates selected
Related Products
Seat sliders Sparco
- High quality seat sliders from Sparco
- Longitudinal mounting hole distance 271 mm
- No FIA approval
- For lateral type mounting, side brackets are required
- If seat is bottom mount type (common in tubular frame seats and reclining seats), sliders can be fixed directly to the seat without side brackets
- Heavy duty version available here
Seat sliders Sparco HD
- Heavy Duty seat sliders from Sparco
- Sturdier construction vs. the standard sliders
- Mounting hole longitudinal distance 271 mm
- No FIA approval
Adjustable VESA plate
- Angle-adjustable mount for VESA 75 / VESA 100 compatible displays
- VESA 100 (100×100 mm pattern) is by far the most common type (also in 49″ Ultra / Super Ultra Wide displays)
- Can be mounted to practically any flat surface
- Usually mounted to aluminum profile (see pic)
- Angle can be adjusted without ‘steps’ as the adjusting is done with the M6 bolts
- This way the user can fine tune the angle / alignment exactly as wanted
- Included:
- M8 bolts – fixing the mount
- M6 bolts – angle adjustment
- M4 bolts – screen mounting (thread length: 10 mm)
- M4 spacers – screen mounting, used if necessary, depends on screen. Lengths: thread 8, body 10 mm
- Availability: 1 pc or 3 pcs
Trak Racer TR160 MK4
The TR160, the King of the Rigs, has been designed with experience gained since Trak Racer started in 2008. The base structure is 160 × 40mm high-end aluminium T-Slot extruded profile, anodized in black.
Your choice of wheel mount will be supported by 160 × 40mm high-end aluminium T-Slot extruded profile wheel uprights, also anodized in black and supported with Trak Racer-Signature Corner Brackets – mounted to the side for additional support.
Wheel bases, pedals and other compatibility ⇒ scroll down.
Need a display stand as well? Click here
Direct Drive Mount
- Compatibility:
- SIMUCUBE 2 Sport, Pro, Ultimate
- SIMUCUBE 1 and other ‘previous generation’ Direct Drive motors with MiGE 130ST 20/30 Nm motors, for example VRS Direct Force Pro
- Adjustable tilt angle
- Can be mounted basically to any flat surface
- Mounting pattern: 210 mm x 40 mm (width / depth). Holes are for M8 bolts and min. M6 is recommended.
- Fits the industry standard 80/20 aluminum profile when spec 40×80 mm or above is used
- Material: 4 mm steel
- Matte black
- #technotactical
Display Stand HD
- Heavy duty stand for displays up to 65″
- VESA 100 and VESA 75 compatible
- Available in two colors / finishes:
- Black anodized
- Natural anodized (light grey)
- Bolt-through-profile fixing method used in the vertical profiles
- As the stand is not fixed to the rig
- Distance from user is easily adjustable
- Vibration from a powerful wheel base like direct drive can’t reach the display (which might harm the display over time)
- If needed, TV and other brackets are usually easy to mount to the aluminum slot profile (note: accessories like bolts etc. not included, varies between display manufacturers)
- Measurements
- Floor profiles: 700 mm
- Vertical profiles: 1100 mm
- Inner width: 700 mm
Trak Racer TR120 MK4
The TR120 has been designed with experience gained since Trak Racer started in 2008. The base structure is 120 × 40mm high-end aluminium T-Slot extruded profile, anodized in black.
Your choice of wheel mount will be supported by 120 × 40mm high-end aluminium T-Slot extruded profile wheel uprights, also anodized in black and supported with Trak Racer-Signature Corner Brackets – mounted to the side for additional support.
Wheel base, pedals and shifter compatibilities ⇒ scroll down.
Need a display stand as well? Click here
Mouse plate
- Can be mounted to alum. rig or almost any other material with the included angle bracket (see pics)
- Width 290 mm, depth 210 mm
- Steel with 3 mm thickness
- Surface: black powder coating
- 3 x countersunk holes for M6 bolts (included)
- Included in delivery:
- M6 T-nuts for alum. profile
- 40 x 40 alum. profile, L=440 mm
- Angle bracket and bracket cover for fixing the profile to a rig
- 2 x M8 t-nut
- 2 x M8 bolt
EN 
FI
Reviews
There are no reviews yet.